Product Description
MG Silver Conductive Epoxy
MG Chemicals Part Number: 8331-14G
Forms high strength conductive bonds
This two part silver epoxy offers high electrical conductivity and strong conductive bonding. Use in place of traditional soldering on heat sensitive components. Good for repairing defective traces and creating jumpers on boards. Can be used as an effective heat sink adhesive. This Conductive Silver Epoxy comes in two 7g syringes.
This epoxy adhesive can adheres not only on most of the metal surfaces (aluminium, bronze, brass, copper, steel etc.) but it can also well adheres on glass, wood, plastic, paper, fiber & rubber surfaces as well.
Specifications:
Specification |
Test Method |
Result |
Mechanical Properties |
Tensile Strength |
ASTM-D-638-02A |
911 psi |
Elongation |
ASTM-D-638-02A |
0.3 % |
Compressive Strength |
ASTM-D-695-02A |
1100 psi |
Flexural Strength |
ASTM-D-790-03 |
2,500 psi |
Shear Strength |
ASTM-D-732-02 |
234 psi |
Cantilever Beam
(IZOD) Impact |
ASTM-D-256-02 E1 |
0.39 ft lb ft / in |
Electrical Properties |
Volume Resistivity @ 25°C |
MIL-STD-883E Notice 3, method 5011.4, paragraphs 3.5.8, 3.8.11.1 (Covered Under A2LA Accreditiation) |
0.18 ohm · cm |
Electrical Resistance (in ohms) |
|
|
Sample Size |
|
3mm x 3mm x 1mm |
Base Material |
|
Plastic cap |
Results: |
|
|
Uncured Material |
|
no reading |
Heat Cured
(at 65°C for 15 minutes) |
|
0.8 ohms |
Air Cured
(at room temp. for 5 hours) |
|
0.2 ohms |
Electrical Resistance
(in ohms) |
|
|
Sample Size |
|
30mm x 25mm x 1mm |
Base Material |
|
Fiber glass epoxy |
Results: |
|
|
Uncured Material |
|
no reading |
Heat Cured
(at 65°C for 15 minutes) |
|
2.5 ohms |
Air Cured
(at room temp. for 5 hours) |
|
4.0 - 6.0 ohms |
Thermal Properties |
Thermal Conductivity |
ASTM E 1461 |
in W/m·K
(BTU in /(hr ft2 F) ) |
25°C |
|
0.903 (6.27) |
50°C |
|
0.893 (6.20) |
100°C |
|
0.813 (5.64) |
Glass Transition Temperature (Tg) |
ASTM D 3418 |
55.1 °C [131 °F] |
CTE prior Tg |
ASTM E 831 |
38.5 ppm/°C |
CTE after Tg |
ASTM E 831 |
101.8 ppm/°C |
Cure Schedule |
Air Cure @ 24°C (75°F) |
|
5 hours |
Heat Cure:
65°C
/ 149°F
90°C
/ 194°F
125°C
/ 257°F
150°C
/ 302°F |
|
15 minutes
12 minutes
7 minutes
5 minutes |
Working Time @ 22°C |
|
10 minutes |
Minimum Operating Temp. |
|
|
Maximum Operating Temp. |
|
150 °C ( 302 °F ) |
General Specifications |
Mixing Ratio |
|
1:1 |
Density |
ASTM-D-256-02 E1 |
2.34 g/cm3
|
Color (cured material)
|
|
Silver Grey |
|
Outgassing Properties (ASTM E595) |
Cure Time |
% TML (Total Mass Loss) |
% WVR (Water Vapor Regain) |
%CVCM (Collected Volatile Condensable Material) |
10 min@65°C + 24 hours@23°C |
7.16 |
0.06 |
0.1 |
10 min@65°C + 48 hours@23°C |
6.11 |
0.05 |
0.05 |
|
QTY: 1 x (2 syringes) of 2 Part Silver Conductive Epoxy. (14g/0.35oz)
Product condition: New